A pool technician vacuums a green, algae-filled backyard pool during a cleanup.

Cleanup

How to clean up a green pool

A green pool is usually a sign that algae has gotten ahead of the sanitizer, the circulation, or both. The cleanup is work: make the water fit for chlorine to work, brush what you can see, run and clean the filter, and keep treating until the water is clear and the sanitizer reading holds. Do not swim until that is done.

This guide assumes a typical residential chlorine pool. Read the product label before you add a large dose of anything. If you need a refresher on test numbers, use the pool chemistry guide. If you just took a cover off for the season, keep the opening steps in mind so the equipment is actually ready to run.

In this guide

  1. Safety notes
  2. Step-by-step cleanup
  3. When to call a pro
  4. Questions owners often ask

Step by step

  1. Keep people out and make sure the equipment can run

    Close the pool to swimmers until the job is finished. Then look at the equipment. A green pool will not clear if the pump is air-locked, the filter is packed, a valve is closed, or the water level is below the skimmer. Check the water level, empty debris from the skimmer and pump baskets, and confirm that the pump primes and moves water through the returns.

    If the pump will not run, the filter is damaged, or you see standing water on electrical equipment, stop and call a technician.

  2. Test the water and look for a simple cause

    Test free chlorine, pH, total alkalinity, and, if your kit allows it, cyanuric acid and calcium hardness. In many green pools, free chlorine is at or near zero and pH may be high. Note the readings before you add anything.

    Not every green tint is algae. Water that is clear but green or teal, especially with staining, can be a metals problem, often copper, and is not treated the same way as a cloudy algae bloom. If the water is cloudy or slick, you are likely dealing with algae and can keep going with the steps below.

  3. Balance alkalinity and pH so sanitizer can work

    Chlorine works poorly when pH is high, so a cleanup goes faster if you bring total alkalinity and pH into a normal range as you begin treatment. Common targets are total alkalinity of 80–120 ppm and pH of 7.2–7.8. Use the product labels to raise or lower those readings, and do not add acid at the same moment you add a chlorinating product.

    You do not have to have every number perfect before you start brushing, but you should not dump shock into water that is wildly out of range.

  4. Remove debris, brush every surface, and vacuum

    Skim leaves and other debris. Brush the walls, steps, corners, lights, behind ladders, and the floor. Algae clings to surfaces; if you only add sanitizer and do not brush, you can leave a film that comes back. On a vinyl liner, use a brush meant for that surface so you do not scuff the liner.

    Vacuum as the loosened material settles. If your plumbing can vacuum to waste, that is often the better path when the load is heavy. Add water to keep the level in the skimmer, and plan to brush more than once a day while the water is still green or hazy.

  5. Treat the algae according to the product label

    Once the pump is circulating and pH is not sitting high, add a chlorinating shock or other algae treatment exactly as the label directs for a green or algae-affected pool. The amount depends on the product, the volume of the pool, and how bad the bloom is. Stabilizer (cyanuric acid) also affects how much sanitizer the water may need. If the label gives a dose for visible algae, use that dose, not the everyday maintenance dose, unless the label says otherwise.

    An algaecide is optional and is not a substitute for brushing, circulation, and enough sanitizer. If you use both a shock product and an algaecide, read both labels for compatibility. Never mix products in a bucket, and stay out of the pool for as long as the label requires.

  6. Run the filter and clean it as it loads up

    Run the filter continuously until the water is clear, as long as the equipment can do that without a problem described in the manual. As algae dies, the water may look even cloudier for a time. That material has to be filtered out or vacuumed out.

    Watch the pressure gauge. When the pressure rises well above the clean starting pressure, or when flow at the returns drops, clean the filter. Rinse or replace a cartridge; backwash a sand or DE filter as the manufacturer directs, and recharge DE after a backwash if that is your system. A dirty filter will not clear green water on its own.

  7. Repeat until the water is clear and sanitizer holds

    Retest, brush again, and add more treatment only as the label allows if the water is still green or if free chlorine has already fallen back to near zero. A useful check, once the water is improving, is whether free chlorine stays in a normal range after an overnight period. If chlorine disappears by morning, there is still demand in the water and the job is not finished.

    Keep going until you can see the bottom clearly in the deep end, the slick feel is gone, and free chlorine remains in the common 1–3 ppm range overnight. Do not swim until those conditions are met and any label wait time has passed.

  8. Return to a normal routine so it does not come back

    Once the pool is clear, keep free chlorine in range, test regularly, and do not let the pump sit idle for long stretches in hot weather. Empty baskets, keep the water level in the skimmer, and clean the filter before it chokes off flow.

    If the same corner goes green repeatedly, look at circulation, a clogged return, or shade. Persistent spots that survive a thorough cleanup are a reason to bring in a technician.

When to call a pro

Call a pool technician if the pump or filter cannot run, if the water is still green after a careful, repeated cleanup, or if you see black or tightly clinging spots that do not yield to brushing and labeled treatment. Call if you think the color is from metals rather than algae, if a liner is damaged, or if you would rather not handle large amounts of chlorinating products or acid.

Browse the market pages on Pool Tech Near Me to look for a local technician. Listings are still being added. We do not service pools ourselves.

Questions owners often ask

Is green water always algae?

No. Cloudy, slick, soupy green water is often algae. Clear green or teal water, sometimes with staining, can be caused by metals such as copper. If you are not sure, get a test that includes metals before you keep adding algaecide.

How long does it take to clear a green pool?

A light haze can improve in a day if you brush, circulate, and clean the filter. A dark, pea-soup pool can take several days. The pool is done when it is clear and the sanitizer holds, not when a set number of hours has passed.

Can I swim when the pool is only a little green?

No. Wait until the water is clear, you can see the bottom in the deep end, and the sanitizer and pH are back in a normal range. A light tint is still a sign that the cleanup is not finished.

Should I drain a green pool and start over?

Draining is not the first step, and it can harm some pools. Clean, circulate, balance, and treat first. Consider a partial drain only if a technician, or a very high stabilizer or hardness reading, gives you a reason to replace water.

Why did the water look worse after I shocked it?

Dead algae often cloud the water before the filter catches them. Keep circulating, brush, vacuum if needed, and clean the filter as the pressure rises.